
As part of my project to recreate a medieval chained library, I’m exploring historical corner bosses: metal fittings used to protect books by lifting them off the table. I’m planning to make a great many of them to protect the books I’m binding. This blog looks at the various shapes and sizes to be recreated.
The easiest way to obtain corner bosses is to buy them, but options are limited. You can either use upholstery tacks, as I did for my first Carolingian binding, or order from a specialist supplier catering to professional book restorers. The former looks underwhelming; the latter costs upwards of a few hundred euros just for a single book. So I began to wonder: can’t I make them myself?

Before recreating anything, I prefer to begin with research. So once again, I turned to e-codices.ch, a treasure trove for anyone interested in medieval bindings. There, I found numerous examples of fasteners. Of course, we can’t always assign these to a specific date; many may have been added later in a book’s history.
So once again, I turned to e-codices.ch, a treasure trove for anyone interested in medieval bindings.
I ultimately narrowed my study to fasteners I could realistically produce myself. That ruled out corner bosses made through casting or techniques like raising, chasing, or repoussé. What remained were simple forms, the bosses shaped like domes or resembling hats. Let’s take a closer look…
‘Dome’ shape corner bosses












Half-spherical bosses appear as one of two shapes typically found attached to digitized manuscripts on e-codices. Their pictures show shapes ranging from nearly flat to almost spherical. Standard descriptions list them being of either iron, copper, brass or bronze. And they also appear to be the smallest bosses around, being consistently smaller than the ‘Hat’ type bosses shown below.
‘Hat’ shape corner bosses












Hat shaped bosses consist of another model I often found on manuscripts. This type consists of mostly flat surfaces, with about half its surface area raised compared to the edges. Furthermore, I didn’t find any Hat shaped bosses made of either iron or copper, only brass or bronze. Their size also appears limited to approximately 20mm to 30mm, though these certainly consist of the bigger corner bosses.
Vestigial corner bosses




Finally, I found some vestigial corner bosses. They’re of some interest, considering they provide imagery of how they would’ve been attach to a manuscript. The few examples shown above show outlines whose measurements vary between 15mm to 33mm. Each hole for the attachment measures about 3mm across, so that must’ve been some pretty thick nails for modern standards.
Corner Boss Measurements
| E-codices MS. | Type of boss | Outer diameter (mm) | Inner Diameter (mm) | Center Height (mm) |
| min0048 | Dome | 28 | — | 6 |
| min0016 | Dome | 27 | — | 7 |
| 0011 | Dome | 17 | — | 6 |
| min0003 | Dome | 17 | — | 5 |
| 0102 | Dome | 16 | — | 5,5 |
| F-II-0020 | Dome | 6 | — | 2.5 |
| 0187 | Hat | 32 | 15 | 8 |
| 0581 | Hat | 30 | 18 | 9 |
| 0004 | Hat | 30 | 16 | 11 |
| 0629 | Hat | 28 | 14 | 6 |
| 0006 | Hat | 27 | 14 | 7 |
| min0015 | Hat | 22 | 12 | 6 |
| 0453 | Vestigial | 33 | — | — |
| Wett0004 | Vestigial | 15 | — | — |
| 0710 | Vestigial | 15 | — | — |
| 0689 | Vestigial | 15 | — | — |
The table above shows the measurements for each type of corner boss, divided into three categories and presented in the same order as the examples discussed above. I included the reference to each manuscript, the height of each corner boss, their outer diameter, and — if it is a Hat type — the inner diameter (which refers to the smaller, raised circular area). The measurements for the inner diameter, as well as its height, were calculated based on its outer diameter.
Since the rulers only appear in one image showing the front cover, I couldn’t measure the inner height of the bosses directly. Therefore, I calculated these through a scaling method based on known dimensions. By using the measurable outer diameter of the circular object (visible in both front and side views) as a reference, I established a pixel-topixel scale ratio between the side and front views. Then, I measured the boss height in pixels and adjusted it using the calculated scale ratio to match the scale of the front view. Finally, I converted this adjusted heght into real-world units using the ruler visible in the front view image.
Next step(s)…
Now knowing that the shape and measurements of the corner bosses means their design is straightforward. But making them will be the real challenge. Attaching the nail so I can attach them to a binding is not an issue. That is simply a matter of soldering. But getting them into that shape, that’s the hard part. For the dome shaped bosses, a simple dapping block should suffice. But the hat type bosses likely require something like a die and punch method to get into that shape.
Further reading:

Book fittings: The archaeological reconstruction of (post-)medieval books by Berna van Wijk, a master thesis in Dutch book fittings providing many references and examples of not only corner bosses, but all sorts of fasteners found on medieval manuscripts. Additionally, this thesis also goes into detail on their origins, manufacture and chronology.

Hugging A Medieval Book by Erik Kwakkel explores various “body parts” of medieval bindings, describing the many interesting features that one might find on them.

The Faith that Binds: Swiss Anabaptist Devotional Bookbindings in Early America, while primarily devoted to the binding, offers a great resource for fittings founds on early modern books.
References:
This article incorporates various image snippets shared under a Creative Commons license, particularly in the galleries illustrating the dome, hat, and vestigial corner bosses. The original sources and copyright status of these images are detailed below:
- Aarau, Aargauer Kantonsbibliothek, MsWett 4 under CC0 1.0 Universal.
- Basel, Universitätsbibliothek, F II 20 under CC0 1.0 Universal.
- Einsiedeln, Stiftsbibliothek, Codex 629(258) under Attribution-NonCommercial 4.0 International.
- Engelberg, Stiftsbibliothek, Cod. 102 under Attribution-NonCommercial 4.0 International.
- Engelberg, Stiftsbibliothek, Cod. 4 under Attribution-NonCommercial 4.0 International.
- Porrentruy, Archives cantonale jurassiennes, 187 J 35e under Attribution-NonCommercial 4.0 International.
- Schaffhausen, Ministerialbibliothek, Min. 15 under CC0 1.0 Universal.
- Schaffhausen, Ministerialbibliothek, Min. 16 under CC0 1.0 Universal.
- Schaffhausen, Ministerialbibliothek, Min. 3 under CC0 1.0 Universal.
- Schaffhausen, Ministerialbibliothek, Min. 48 under CC0 1.0 Universal.
- St. Gallen, Stiftsarchiv (Abtei Pfäfers), Cod. Fab. VI under Attribution-NonCommercial 4.0 International.
- St. Gallen, Stiftsarchiv (Abtei Pfäfers), Cod. Fab. XI under Attribution-NonCommercial 4.0 International.
- St. Gallen, Stiftsbibliothek, Cod. Sang. 453 under Attribution-NonCommercial 4.0 International.
- St. Gallen, Stiftsbibliothek, Cod. Sang. 581 under Attribution-NonCommercial 4.0 International.
- St. Gallen, Stiftsbibliothek, Cod. Sang. 689 under Attribution-NonCommercial 4.0 International.
- St. Gallen, Stiftsbibliothek, Cod. Sang. 710 under Attribution-NonCommercial 4.0 International.
